How to Pair Goggles and Controllers to the DJI Avata 360
In this guide, we will explain the process of pairing goggles and controllers to the DJI Avata 360 drone. This is particularly relevant for users who have purchased the drone separately from the goggles and controllers.
Understanding the Need for Manual Pairing
If you have purchased the Avata 360 with goggles and a controller, these devices are typically pre-bound. However, if you acquired the drone alone or with a controller while already owning goggles, you will need to update the firmware of your goggles and manually pair them with the drone. This process will be demonstrated in the following sections.
Compatible Goggles and Controllers
The DJI Avata 360 is compatible with the Goggles 3 and Goggles N3, as well as the Motion 3 and FPV 3 controllers. This guide will focus on pairing the Goggles 3 with the Motion 3 controller, but the steps are similar for other compatible devices. Ensure that you have the latest version of the DJI Fly app installed to facilitate firmware updates.
Powering On and Pairing the Controller to the Goggles
Begin by powering on the goggles and the Motion 3 controller. It is advisable to ensure that all devices are fully charged. If the controller is not already paired with the goggles, follow these steps:
- Press and hold the power button on the controller until it starts beeping.
- Press and hold the power button on the goggles until they pair, confirmed by a series of beeps.
Updating the Goggles Firmware with the DJI Fly App
Before pairing the drone with the goggles, it is essential to update the goggles’ firmware. Connect the goggles to your smartphone using a USB-C cable and launch the DJI Fly app. The app will prompt you to download the latest firmware. Once the update is complete, disconnect the phone, as the goggles will now be ready for pairing.
Switching the Goggles to Avata 360 Mode
To pair the DJI Avata 360 with the goggles, you must first select the Avata 360 mode in the goggles’ settings. Use the 5D button to navigate the menu:
- Press the side button to access the menu.
- Select “Status” and then “Switch.”
- Scroll to select “Avata 360” and confirm your selection.
Pairing the Drone to the Goggles
With the goggles set to Avata 360 mode, you can now pair the drone:
- Press and hold the power button on the drone until it beeps.
- Press and hold the power button on the goggles to enter pairing mode.
Once paired, you should see a visual feed from the drone’s camera through the goggles. This pairing process only needs to be done once for each device.
Pairing the DJI RC 2 to the Avata 360
If you have an RC 2 controller, you can also pair it with the Avata 360. Ensure that the RC 2 has the latest firmware by connecting it to the internet. To pair the RC 2:
- Power on the Avata 360.
- Select “Connect to Aircraft” in the RC 2 menu and find the DJI Avata 360.
- Switch the firmware on the RC 2 to Avata 360 firmware and confirm.
- Put the Avata 360 into pairing mode by pressing and holding the power button.
Switching Between Controllers and Device Binding
Once the RC 2 is paired with the Avata 360, you can switch between the RC 2 and the goggles without needing to repair them each time. Simply power off the RC 2 and power on the goggles to connect automatically. However, you will receive a message regarding device binding, which is necessary for DJI Care Refresh and Fly Away Coverage. This binding must be updated whenever you switch controllers, which requires internet connectivity.
Conclusion
This guide outlines the steps to pair the DJI Avata 360 with goggles and controllers. Following these instructions will help ensure a successful setup for your drone experience.
This article is based on a video from Shawn at Air Photography, who provides further insights on his YouTube channel.